Tuesday, June 09, 2009

More progress

Hello folks.

The nice weather and a lull in studying has seen a little progress on the MG.
I deferred getting the engine going till I can afford some special fuel hose and Imperial nuts/bolts for the fuel tank.
The rear LH wheel arch was still needing work (inner wheel arch- outer portion ) .
I had put off attempting this for a long time since, read below.
I did actually buy a repair section from the MG hive last year, £60 , for my birthday, along with several other panels.
However at the time, I'd already cut the rust away and fitted the complete real rear wing over it. But, then I make a complete novice error. I realised I'd bought the WRONG side rear repair section. It was a right outer - inner section, I needed and I had a left. Hay hoe.
So i did use it on the correct arch several months ago, see much earlier post, and remembered it was a swine to do.

Nevertheless, I set to full of determination.
I had no money but some enthusiasm. It was all i could do.
With rear jacked up and head in small confine of wheel arch. I should say that I had to roll the car onto the road, reverse and push back tuther way into drivespace ,so its pointing the other way, again. Thank you Son No 1.
I'll hammer some sections to fit. Three of four pieces curved round, lipped and curved the other way should be simple enough.
I even went green and recycled the old doorskin to use for said patches.
I had a set of the correct hammers and dollies- no guesses where I bought them from !
How hard can it be ?
After at least 2 hours............. simples !.................VERY VERY HARD. I gave up. Almost.

Then I remembered.

In a moment of e-bay purchasing way back when I was employed and in full control of our finances I did buy one VW GOLF ( Rabbit for our colonials ) outer left wheel arch repair,

WHY I hear you ask ?

Well look further down at the lovely Maroon example. It looks fantastic with very subtle flared wheel arches. I contacted the owner and he gave me the details. Mk 3 Golf rear arches are a near perfect fit for all MG arches. So i bought one. £20 from the usual source.
I had a brainwave........not often i get one but a good one at that.
If it is turned arse about face and maybe cut into 3 or 4 sections a new inner arch could be fabricated.
Why not. correct shape with lip. right curve. clean. smooth free and available.
To press I've done two of the four sections and left them there clamped in-situ.
What is horrible is using the wire wheel cup on the grinding machine. Flat on back looking straight up at almost invisible ( since my goggles are rather scratched and contrast of sky and dark wheel arch make it impossible) edge with a fine mist of 33 year old underseal coating my mouth, hair, eyes, nose and teeth. It was about 10 inches from my forehead, so a slip would have really spoilt my day. I'm scared enough of the grinder as it it anyway.
I looked like I'd been down a mine for months, ergghhhh. And there's still more to do, then weld.
Next post will be photo of job done, hopefully.

Once my exams are over I'll crack on and do as much as possible to get the rolling restoration underway. I reckon I need :-

6 rattlecans of primer
Fuel line - tank to sender
Fuel tank nuts/bolts
RH wing bolts
Rear springs - Lowered type
Small drop arms- rear
Complete Poly bush set
Front Brake discs and pads
Rear brake pads
Front chrome windscreen surround
Front windscreen rubber
Rear screen rubber
Door rubbers
Tailgate rubber surrounds.
Seam sealer

The rest I can live without for the now rolling resto. I hate the seventies Orange/brown/white stripes of the seats though.

That all as far as I know........................................!!!
Yes it is quite a lengthy list. But this time 3 years ago it was unthinkable i could even make a list.

So just a small problem of 3 exams to pass, summer job to find and I'll be making real progress.