Tool trouble then rapid progress

Here's the part I'm damn proud of.

It involved bending a section of the curved rear valance ( above the square hole) then welding in place and having a 5/10mm lip to place the flat plate onto.

The large vertical weld is where the rear valance and wing end did not meet exactly.

I placed a strip of steel approx 1" wide to the rear, bent to fit the curve and welded inplace.

I managed to fill most of the non meeting edges with weld.

The flat plate that rests in the base of the pointy thing and upto/on the rear boot corner was quite tricky. I got through lots of cardboard making the right shape template.

Still, it all went very well with no probs...............the secret to welding is grind all the things nearby shiny, get a good earth and listen to the weld..............like rapidly cooking bacon.



The only Blot on the landscape was the angle grinder dying.

Ma in Law bought it for me last x-mas from screwfix. Not a top make ( NOTE..always buy Bosch if your serious) but its been the most used tool and definitely a requirement.

However, one day it just did not switch on.

Checked the fuse....ok

Checked the kitchen socket....ok

Unpluged and removed the disc and guard...........scary stuff as this tool scares the life out of me.

Then I noticed two protrusions each side of the main body with a large screwdriver slot in the end. Removed these and the commutators sprang forth with a tiny blob of an excuse for a carbon block.......................Disaster, should I persue the probably frustrating and longwinded course of new parts through Screwfix, or should I source locally.

Anyway, since the rains was still with us I decided on local. B&Q ect, shed no light or idea on tool spares.

In fact I dont think any of the staff even knew what a motor commutator was.

Now, may I get on my high horse here. B&Q ect may be cheap, convenient and always open but there not a patch on" proper" hardware places. We have two in my town.

One just like"open all hours" for hardware only. Its amazing. Ask one of the elderly staff for a lock and they will have it all, and explain about 2,3 and 5 lever mortices, ease of installation and price and insurance complications and reliability. Same goes for aluminium ladders, parrafin,

Chicken wire, hinges, wheelbarrows, hammers, bolts and screws + trillions of other stuff.

All served by people friendly and happy and willing to talk and dressed in regulation stores issue Brown smock. Thats just one place.

The other place is for things electrical/electronic.These guys know it all, have it all, but are on a slightly different planet. It scares me a little.

So in I waltz with one mangled commutator. Have you got one of these ?

No, but we have on similar that you can "modify"

Well, for £2.30 why not.

Thats when the probs started. The carbon block was too large so I filed it with my swiss file, on the worktop in the kitchen.......................Big mistake, the dust is immoveable and gets everywhere. Wifey not happy.

Moved outside to workmate and rushing due to fact that imminent heavy storm due.

Still difficult to insert and remove carbon block. Then cover screw would not screw in totally.

Snipped spring shorter. Still no joy. Bent copper ends from carbon block/copper wire in several shapes, still no joy. However, shaking said grinder did momentarily show some life.

Anyways, to cut a long story short I buggered one and re-used the old one which was OK and fiddled the other eventually after lots of shaking and "gentle taps on the plastic retaining screw".

It now works...................thank **ck for that. It was almost touch and go between throwing it away and being electricuted in the rain outside.



Now we've had some respite in the rain the progress above has been made and not a small amount of filling and sanding.

Look......................................rapid progress.

Hours of sanding the rear lower valance applied by the previous owner left no nasty horror sories. Only a 50p sized hole in the very centre of the R/H crossmember end. Easily remedied by some fancy shaping of a 1mm thick steel and good welding/ filling skills.

Even after a good coat of primer some low spots were evident, so another round of filling and sanding. I must say this is very ffffrustrating. The different grades a sandpaper, sanding block, dust, mess, armache and annoyance that a pristine shape don't emerge.

So I moved onto removing the complete exhaust. Easy enough on the length of the car.

Easy enough on five of the six nuts under the manifold although three were a bit fiddly.

The six'th (NOT SIKTH, which is how annoying people pronounce it) however seems impossible to get to. The shaft of the ratchet extension is too thick, the engine base/sump flange won't allow the the socket to sit on fully since the extension is not perfectly vertical.

So a point to ponder on whilst the wifey tries to fill my head with DIY projects and things to do of a summer day in the garden.

More soon folks......................oh by the way visit Ricks site.........He's got more money and tools than me and is making a real good job of it.

http://rick-mgbgt.blogspot.com/