And yet another list of to-do's

Alzheimer's must be setting in. I just realised I've repeated most thing in the last two posts.
So here is the definitive list I made this morning on the status so far, in no particular order.

1/.   Replace both rear tyres.
               It would appear these have only lasted 15 years plus and can no longer hold air. What I did with the front cost me a tenner ( £10 =$ 14.5) having a local company fit 2 good but bald-ish scrappers. Albeit they are low profile, but sealed up to the hilt and with new valves. Next day off will see me visit said establishment for a repeat ( but not low profile though)

Sadly I see no point in buying real tyres yet.

2/.    Buy and fit new brake servo. Had the money for it last year but frittered it away on god knows what. Commonsense say to replace rubber hoses to front too, and free of the cylinders. I replaced the caliper pistons, seals and discs ( rotors ) a few years back so I must add more effort to make them work and appear new again.

3/.   Weld/repair lower valance. I converted from RB to CB and the new holes for the side lights/indicators looks a bit dogs dinnerish with little support below.  I have to find the Jigsaw first, no mean feat as I've not yet done this years clean up of the shed and outhouse.

4/.   Yet more expense. The small heater radiator is leaking. I'm not letting this bother me yet as I'll bypass it with some jiggery pokery of hoses and it won't affect the running of the car. ( Thats if it will run after this years lay up)

5/. Buy and fit Indicator stalk mechanism. Nuf said, broken through sheer stupidity and Lostsock logic.

7/.   Re-set tappetts. Sounded very noisy when last run, or was it timing chain rattle ?

See what you think

8/. Check oil/water levels......... !!

9/.   Check dash bulbs and replace.......fit dash.........re-paint in crinkle finish ?   naah, its good to go and has only a little patina of  " old car"

10/.   Re-cover dash top panel. Not as easy as it sounds. Need hardboard, foam and jigsaw !!!

11/.   buy front bumper fitting chrome screws. A little vainglorious but hopefully it will at least look like being finished............from the front....low down, anyway.

12/.Clean engine bay..........big job and difficult with engine and all ancillaries there   !

13/.   find/acquire starter motor bolt.........for some reason the top bolt is different from the bottom and I can't find it..............or remember weather its the top or bottom I need.

14/. Sand spoiler. Well documented in previous posts. Did 3/4 of it today. Sanded off most of the ...nay all of the real primer that reacted. Even managed a quick tickle with rattle can of primer. Wish I had not. Shows up all the flaws in "too course sanding". Mostly wet an drying this today but getting there.

More next week folks.

Wot a faff

So, the saga still continues.

Sorry I've not posted of late. The trouble is good ole Google. I have over the years got several google accounts + the kids accounts set up on this laptop. And that's where the trouble starts, trying to log on now its all controlled by Google.

Anyways, I've written down the log on Name and password and linked it to my iphone, so, hopefully some posts on my progress with images directly from my phone. I did say hopefully, as I always have trouble with the youngster specific apps like itunes and Google+.

To fill you in regarding the MG. Nothing has happened since the last post last year.  I've still not purchased the master brake cylinder yet, but since it was birth month I may have enough cash to buy and fit.

The nice weather this week has seen me cut and strim lawn, replace 6' x 8' trellis panel after hammering in 2 fence posts, blow away leaves from autumn, paint said trellis and archway + shed front. I had only one day for MG stuff and that was spent removing all the tools and stuff, cleaning, oiling and re-organising as they suffered a major ingress of water this year due to a leaking outer cover.

Next job up is to get 2 tyres ( scrap ones) from local friendly tyre fitting company so I can at least roll the MG fore and aft to sweep the drive. Then fit master cylinder and maybe just may be run her up/down our little cul-de-sac. Todays fact..........the word Cul-de-sac is not recognised as a word or entity in French.

p.s The spoiler looks nothing like this now. In my wisdom I coated it in "proper" primer. Its reacted and needs sanding off again.....ho...hum !

More soon folks !

Now the difficult bit/s........Electrics !!

So faithful fans,  I'm still at it albeit slowly due to lethargy, work and lack of finances.
I last left the car with the new ST spoiler loosely fitted and the Bumper bracket attached. The Brake master cylinder has been removed during the last attempt at seal replacement as it broke on the end so a new one is needed. I've had the cash for the replacement for some time but not the inclination to fit it.

The enormity of whats left to do has been nagging away at me for some time and often thought of packing it all in, especially since my daily hack the Peugeot 207 has developed an annoying limp home issue.

So today with 3 days off and a nice sunny day I set to to looking at the dash re-fitting and vynyl top re-glueing + crash pad. Bad move !!

The good news is I have finally removed the steering wheel after 2 years of trying. Damaged the nut and thread on column though, fortunately not much.

The bad news is that I've buggered the RH indicator mechanism, lost some small but vital parts and snapper one important part ( also tiny and un-fixable). That's another £30 part needed !!!
When will I ever learn the old motto.... " If it aint broke don't fix it !!"
I had a loose purple wire bullet connector (Male) adrift from somewhere on the underside of the stalk mechanism and needed the wheel off and said mechanism. As  I've said I've now done both but  could not resist taking the RH unit apart to see where/how/ why the female bullet connector was to affect a repair.
Hey Ho....another one for the experience bank.

I shall be extremely careful whit the electrics from now on.
I know from all those years back that at least 3 rocker switches disintegrated on removal, the heater pipes were impossible to undo and the dash a complete enigma to free one dark and snowy winter.

So maybe tomorrow I will investigate the dash bulbs and source some wrinkle finish paint to aid the enthusiasm drought. Wish me luck.

Not long Now ?

Just a quick post to let you know I'm not dead and still at the MG stuff.

Its taken me all of 2 hours to get onto the blog to put this post on, gawd I must be getting old.

I'm about to clear out the shed at the bottom of the garden soon and this means only one thing, its summertime....almost !

Since starting as a Radiographer proper a couple of years ago and on the "Rota" it leaves very little time to dedicate to my loved one, let alone having the cash.

However to get up to speed I'll tell you the following since the last post.

1/. Not much

2/. Ma in Laws 80th birthday soon, that means its been 10 years since I bought it and thought I better get it finished !

3/. The weather has been rubbish during winter so the first jobs will be cleaning off any rust and puddles accrued.

The engine runs, albeit a bit "tappetty", allthough I set the clearances I think its the timing chain/tensioner making the noise. Find the vid and have a listen, let me know your views.

The spoiler is fitted 80%, needs a full set of the correct screws and nuts and attention to the sidelight holes. During removal of the original valance half of the screws sheared , some came out OK some needed the nut behind grinding off.

So, I'm considering an engine bay tidy up, bodge fix on the heater radiator core and buying a new Master brake cylinder. The old one's been on and off so often to mess with the seals that I damaged the cast iron body whacking it against a wooden batten then in frustration a housebrick !

After they are sorted I'll fit the dash ( I'm sure there will be several posts regarding this subject) fit the window and seal mechanisms and maybe front and rear screens. Thats enogh to chew on for now. I'll post more when I actually do something, If good old blogger/google plus lets me back on !

Typical.............!

As last posted re "Perfect Storm", this weekend has seen everything in place except the weather.
      Work has been tough ( and continues to be so for the foreseeable future...good ole NHS) with many off hours shifts and weekends.
However I'm about to start a 6 week period with all weekends off except for one Sunday...whoopee.

So my old friend the weather plays its fickle part yet again. Dull and rainy on and off, windy and changeable.
At least its also halted the DIY too.

 I've just replaced the 90 foot x 6 foot Ivy encrusted fence panels down the side of my property and had a hell of a job too. Most of the panels have been " de-Ivied...?" and a neighbour has had about half of them for his steam engine. I have the last 3 thickly ivy encrusted to dispose of and several panels reduced in size ( i.e smashed to smithereens or fell apart when ivy removed).

The lawn needs a good mechanised rake and I'm sadly behind on the seasonal Easter shed clean-out.
The clean-out is one job I enjoy. It involves emptying the outhouse in conservatory to get out outside the six patio chairs. Then a thorough clean and throw out of (mostly Wifeys) stuff.

Then same to shed. This is where most of my MG stuff is located, most of the internal parts and chrome stuff. Since I'm at that point of putting things back on I'm even more frustrated that its not yet happened due to several factors. Mostly Wifey going full tilt for her finals at Art Uni ( She's responsible for 99% of the "Stuff" in and around the house...her excuse being  its needed for my degree...!)

That's about it in a nutshell. Except I've finally got round to looking at the Blogger settings as to why no comments or listing rating has dropped me like a stone this last 2 years.

So come on....drop me a line, I need cheering up !

Its been too long !!! but I'm still at it

Yes it has been a long time since the last post. I've not lost interest in fact things have been progressing very well.
A quick recap has seen me finish just about all of the bodywork and panels and solve the issue of oil/water mixing in engine oil after the head skim and pressure test.
I must admit this had me worried over the winter of inactivity, however come this spring it appears to have vanished. How ?
I don't really know.
 I emptied the engine of oil of about half and refilled with fresh oil (NOT the cheap Wilko stuff) and set to work trying to get the engine running smoothly.
First was to re-torque the head bolts.
Then adjust tappet clearances.
Then fit stainless steel exhaust and brackets, bought second hand off E-bay for £35 quid. Excellent condition + bought brackets from MGOC £18.
Next removing old rusted on Brackets.
This was not a simple task. The bolts at the rear holding the complex rear exhaust mount are inside a tiny box section and were a swine. I reverted to the angle grinder to get most of the bracket off without slicing a finger or skull part off. The nuts however were inaccessible and well rounding off, same for the centre bracket.
So I soaked them in Duck Oil and left it for another day.
Another day.....
The bolt heads are 11mm....doh. Just when I was well and truly stumped on how to get them off I thought I'd try the more accessible middle bracket first and lo...it (they ) came undone easily with an 11mm spanner.
So same tactic for rear bracket, more fiddly but done with some patience, swearing and filthy head.
Then buy new jump leads ( where oh where have my originals gone?. Suspect a family member but no one owns up)
Read up thoroughly on carb tuning thanks to John Twists excellent you-tube vids.
Re-fit dashboard sort of, actually only connected gauges plug. This looks like its going to be a major fiddly job eventually as it wouldn't even sit where it should under the dash rail, let alone clean and fit all the loose wires everywhere as well as troubleshoot any probs. Hey  ho, another job for later.

Fitted exhaust easily but the manifold nuts were fiddly and needed some clever socket extensions and lateral thinking.
It was while I was supine under the sump spannering the manifold nuts ( Liberally coated with copper grease...my new best friend) I noticed a long standing oil leak (as in years) and where it was coming from.
What looked like a simple tighten up of one sump bolt also needed lateral thinking and a bit of bravery.
It transpires that trying to tighten it was just rounding off the nut........or so I thought. The nut in question was at the very rear of the sump 4" up in a tight spot next to the gearbox. The problem was that the sump mating face has a downward facing lip on its outer edge, I presume to give it some form of strength. This was next to the nut and a socket didn't fit on it very well, hence it was not tightened fully.
              Being a dolt at times I imagined sump off and new gasket, not an easy, good or clean job to do upside down on the floor, also being a tightwad and possessive of my tools I didn't want to grind down a socket.
So I took a lump hammer and blunt pointing chisel and gently bashed the rim outwards some/ enough to get the socket on firmly and apply some/more force. I think its worked...so far.

Whilst starting, nay cranking over I noticed more leaks. Two actually, one oil and one water.
The oil cooler hose where it meets the oil cooler needed a little nip up and job done. More tightening of the leaking exhaust manifold saw me source the water leak, from the footwell/copper pipes underneath to the bulkhead to the plenum chamber (of sorts) to the heater to the matrix. Some years ago I'd refurbed the heater box so it was easy to remove. As we speak the matrix is standing outside full of water with one end bunged up in an effort to pinpoint the leak even further, However this will not detract from the march onwards.
Trouble is, as we restorers know, it does.

Should I get the engine bay looking good or just better, it looks crap now, or carry on with fitting up as a whole ?
Since wifey said I could have £100 quid to spend on pure MGB stuff, I bought the exhaust, bracket and a new ST front spoiler... £35+ delivery.

Its gonna be a bit fiddly to fit since some of the holes in the body valance have their welded on nuts missing from when I removed the original valance a few years ago. Also I can't remember where I put them or what size they are.To make matters worse its not an exact fit to the contours of the front of the car. The spoiler has a squared off flat  middle section !! is this normal ?.

Never mind though as this area is covered up by the (eventual fitting of ) chrome bumper. The re-positioned indicator holes have also left the area below a little weak as some of the "L" shaped body has no vertical lip underneath. Should I weld on ? ( tricky as the piece has two curves,... Fibreglass mat it ? don't improve strength but looks better or Ignore altogether as again its not seen behind the chrome bumper ?

Since the engine runs quite nicely (see vid above) should I :

Continue fitting the dash and electrics ?
Continue adding chrome and glass parts ?
Refurb engine bay ?
Bleed brakes ...or buy new master cylinder ?
Faff around doing bits of all of the above ( most likely outcome)

Another startling discovery made recently after a review of as to why I can't bleed the brakes ( from last summer) was I'd fitted a master cylinder seal the wrong way and trapped one with the retaining pin.
One major problem is wifey has to help me bleed the brakes ( unwilling and bored easily!!) and I don't want to really fork out for a master cylinder if I don't have to.
Some extra money due to a birthday has given me something else to think about buying ( NOT master cylinder amounts) so I'm thinking splash guards.....or maybe some thing else !

I promise to post more often. At least I have six, yes SIX weekends off soon.

Just to remind you, my restoration is like the perfect storm : several elements have to come together all at the same time, viz

1/. Money
2/. time off work
3/. good weather
4/.No DIY or gardening chores to do
5/.Inclination to get up early and know exactly what I'm going to do and how to do it
6/.Not feel tired from work

That's my excuse anyway !!!