More on than off

Above shows the new sill welded in position and a good door gap. Its better than the LH side as then I removed the door ( bad move) However this time i left the door in situ and look, it fits great. I only made one error. A small one at that. I forgot to buy a jacking point when I purchased the sill from MGOC. Not so bad though as I can always weld it on later.



Next job is to repair the Inner wheel arch, replace whole of LH wing, but first make new repair section to rear window base. Its rusted completely through and no new panels are available.

I'm going to bend one at College on their ace bending machine. It comprises of a short vertical piece of say 8mm then the horizontal base with another bend tapering along its length down 90 degrees at say 8mm ( this is where the new wing will attach)

The job thats got to be done that looks a little fiddly is the hole in said window corner. Its a large radius in a 45 degree apex with little or no chance of getting in the scary grinder to dress the welds so I'm thinking I may braze a section in, if only I knew how to braze or had the kit !

I wisely did all this a few weeks before the easter hols, and guess what , ever since its been either snowing, raining, gale force winds or all three so I,m not so frustrated.

The earthquake also put a stop to things for a while.

After hearing what sounded like a dumper truck depositing 3 tons of bricks on the roof and a quick check that we were all ok, a rece showed the chimney stack had reduced in size and came to rest in the conservatory via the tri-ply roof. So my office has been out of bounds for some time till its replaced, the chimney stack has been repaired so we are not living in fear of errant bricks or slates anymore. When the weather is better and money abundant the car bodywork will be virtually done bar a few minor touch ups and cosmetics, then on to the suspension, or engine, or chrome, or carbs.............and on and on.



More soon folks !!

More off than on !

That is bodywork wise anyway. Another glorious weekend and I set too removing the rear wing. I debated long and hard about removing it. I have the cash to buy a new outer sill and new wing ( left over from x-max prezzies) and i have in the shed (for shed read vehicular temporary storage area- non garden bottom orientated-ie i save it in the MG) a partial outer inner wing, brand new. So, i thought i would need all these parts before removing the wing.

The great god Mr Mark Evans says its important to repair the inner wing BEFORE removing the outer................................please forgive the petulance and disobediance Mr Mark ,but you're wrong ! Especially since you don't know MY CAR, previously bodged..big time.
Below is a prime example. Look at said wing removed.

This is the removed wing. Its had a repair panel "sort of " welded aroung the wheel arch. I say sort of since the norm is to replace all of the lower half at the seam/swage line, or joddle a new section/s under the damaged/cleaned up wheel arch. This was neither, just lots of filler over the whole area right down to the rear valance and rear light cluster ( including much gauze below the light cluster) The panel was a doddle to remove for 2/3rds of its connection . The final 1/3rd was a right swine, its the part thats nearest the rear door gap. The actual wing fits over some areas of gently bent ( 90 degree bend with lovely radius) and fits under other areas, all making a nice join at the point you notice most when opening the door. I took me ages to discover the tiny spotwelds, some inaccessible, some invisible most impossible. Surely it did not take this long to remove the other side.,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,!!!!!!No yer great clot!!!!

You bought the car with no rear left wing, remember, all that time long ago, when you were blissfully ignorant of bleeding knuckles, eyes full of grit, pores full of Duckhams and a shed you could actually walk into. So a few gentle taps with the omni tool ( part chisel/part screwdriver/part upholsery prise bar/part rust basher/scraper) some sardine can like peeling with the water pump pliers after a slicing sesion with trusty grinder ( + slicing disc) and yipee.

Tried to work today ( Saturday 2 pm) but despite the sun shining its bloody cold. Only managed to dress up some rusty edges on wing before my toes and nose said no more please. Spent most of following Sunday catching up with college, its still freezing cold out though.

Next job on the list is to Purchase and fit outer sill. Make and weld small tabs to secure A post to sill.
Then remove rust from wheel arch HERE <
Fit new wheelarch repair panel. Weld to rear of new sill.
Fit new wing and weld then repair base of rear light/pointy thing and join with rear valance.

Should keep me happy for a bit, if it don't rain !

Its over.............here comes summer !

Hello peeps

Many apologies for not posting for so long but its taken a good few weeks to overcome the lethargy, depression and general goings on. Still thats what holidays are for, and guess what. Its done the trick. So to prove it here I am smiling the Sunday before new years eve ( the day after the wedding anniversary also)

Yes I know its all Bluey tinted, but daughter number one took it, and was cold standing in bare feet, so rushed it meI thinks. Still it was very cold and getting rather dark though.

Had a very good Holiday so far, with no family Illnesses or other disasters. Had lots of prezzies and booze and snoozes by the fireside. The new additions to the fold Ralph and Ruby ( 5 month old stripey Tiger type cats) are sending us nuts with their antics and ruining the house. In fact we've given up replacing the baubles on the tree after Ralph decided to launch himself from the sofa to the tree innards. Well, actually as punishment to the kids ( They always deserve SOME punishment - almost 14 year old twins, boy- girl, lots of time in the house/bed/bedroom/internet/i-pod/x-box) we decided it was their chore, or no free time.

Clever little dicks, they just banned Ralph & Ruby from the room.

Back to the resto. Finally motivated myself to get stuck in and welded the floorpan strip in.

I did think I would have to spend hours making the strip a perfect fit, but, as in new year resolution, JUST GET ON WITH IT. So I did. No fussing and worrying. No over thinking the Issue.

Here it it tack welded in position...........Note the Hi-Tech clamp of hammer and wood offcut.

And finally welded. Can you see the join yet ?

Its the longest weld I've done so far. Only tricky for half its length because my head, the welding helmet, right or left arm and Steering wheel all wanted to be in the same place.Its dark in there too. And smelly with thick black smoke from the underseal underneath. Counted seven little welding fires which all needed me to extract myself from my semi prone hernia inducing welding position and flap wildly with gloved hand to extinguish them. The photos look nice and clear because of the flash, but in reality it was difficult to see, hard to reach , cold, damp and uncomfortable. But i did it. And without complaining.

Next on the list is this little hole near left foot position and small hole near rear spring hanger. Soon though. Fufferfour's back on a roll and he's got money for new panels !!!!!!!!!!!

See you all soon folks..............................+++++.Rick thanks for the e-mail re moments ect++++

An indifference to life in general

Well readers, as you may guess by the title I've been a little preoccupied of late with life in general.
Work is as tough as ever, my health has been suffering a bit of late and family issues seen to be getting more complex and frustrating. Not to mention college which has moved up a gear and left me feeling vulnerable and a little stupid.
The MG has been left well and truly bottom of my priorities, occasionally flapping and waving its errant blue poly cover whenever rain and wind appears.
The weather since my last post has been very good, however my drive and enthusiasm has not, so several weeks have been wasted. I feel I'm going to regret this when winter finally arrives together with enthusiasm, cash and happiness.
However I'm determined not to let the car be one of the many abandoned projects for sale on E-bay. I must say my doppelganger Rick has given me the impetus not to fail as he is restoring a real basket case and is making a good job of it in similar circumstances, if not with a little more cash and garage.
So why the depression Fufferfour ? you ask.
Well I don't know really.
A level physics at college did not help. Full of young kids all able to grasp thirty five ways of transposing formulae, knowing the answer is in Nm, m/s ( -2) Kj or wotsits.
The other evenings are not the same as I feel its a waste of time as they are catering for the newbies ( combined class from the two last year) who are a year behind a small minority in class.
Still Biology continues to be good and I'm beginning to understand how all the body parts work together.
Work wise has not see an influx of machine orders, the ones won have took ages to build and the other side of the biz has seen a few small victories over the competition. Still its a hard and lonely life on the road with such a large area to cover.
Seven days in Dusseldorf working the "k" show proved to be very tiring and not as exciting as previous. Staying with an old couple in the suburbs was really nice but our new French owner had decided to gatecrash over the weekend so all my French colleagues were very tense and very well behaved, almost boring, for my liking. It still took me at least five days to physically and mentally recover. I think this was the start of the great depression.
That and the lack of activity from British industry on the stand.
The wife and kids continue to argue, bicker, winge, demand and generally frustrate any attempts I have of a happy life.
One event of note in our household is the arrival of Ralph and Ruby. Two tiny kittens that look like darkly striped Tigers. How we love the way they frolic with their tiny skinny legs and button noses.
How I hate the smell emanating from the Poo tray in the dining room.
Still, that was a few months ago and now they are turning into whirling dervishes of mass destruction. It's still funny to see their antics though. Unfortunately their poo still stinks the house out. Roll on Feb when they can leave the house for the big bad world outside.
The MG was left with a long strip of about 1" wide cut from the floorpan where it meets the outer sill, and the last 3" of the outrigger cut away. I've since bought a new outrigger and jacking point during a brief diversion to the MGOC last month. Whats difficult is welding the repair panel ( Cut from the opposite sides unused repair panel) in. The steering wheel is in the way. I tried for about 2 hours to bash it upwards from its splines without damaging the soft plastic base. It transpires one of the famous BL service tools ref BL-vb10073 part 6a is required. I say famous because no one has ever seen any of the recommended service tools. There is also two further small holes in the drivers side floor. One near the rear spring hanger, which has for some reason been repaired previously without trimming the excess steel away, and another at the base of the transmission tunnel/floorpan, near where your left foot would rest. I don't think these will present too much difficulty though. ...........................famous last words !
I have a inner rear arch panel to fit ( Birthday present in May) together with a new rear wing and maybe rear sill repair section and complete outer sill ( yet to be purchased). I also need to fabricate a section of about 10" long with two 90 degree bends to repair the window frame base where the wing is welded to.
Then the major bodywork is almost complete....................hehe.....easy word almost !

Getting there

The last few weeks ain't seen much activity.

However, the A post nightmare has ended. Yes I bit the bullet and welded, cut, ground, templated, cut, ground & welded ad infinitum. + not a lot of body filler.

I must say sanding filler is not my favourite pastime. God is it boring. Unfortunately its necessary and vital to get a good look to the finished car.

So, the A post then......................see the finished result below !

This is the finished result after lots and lots of very fiddly welding in of small curved pieces of steel. Its integrity is good and the filler only hides the welds too inaccessible for the grinder.

However, its the wing join that I'm most proud of. This took some welding in of curved steel and was much easier than I first thought. In fact I pondered hours and hours on how to repair it and kept putting it off till the last moment. The filler sanded a treat and lots of offering up the wing made the join perfect.

What was a constant source of frustration is the front RH wing. The LH wing had lots of welding done on the captive nuts and a new bottom rear edge.

So I was prepared for the worse.

After venturing to the bottom of the garden and behind the shed to unearth the wing I had a pleasant surprise. The captive nuts were fine...............yipeee.....some luck at last.

Booo.................................................................. remembered the wing also had some accident damage to the front around the grill aperture.

But, thought this would be easey peasey to repair, a few whacks and job done.

Wrong, wrong and wrong again.

The area affected is in a sort of zig-zag shape, so I thought a few whacks would sent it nicely back from where it came.

Well about 2 weeks later, several bleeding knuckles, C1 compressions of the spine and picking up a fallen wing from the trusty workmate I'm somewhere near.

Panel beating complex shapes is definitely NOT easy. This was made worse by the fact that whichever way I positioned the wing it needed to be nose down ( on the floor) and tilted up about 70 degrees whilst simultaneously beating it with the precision hammer, which in turn caused the wing to fall over and/or slip sideways. I think I moved 15 yards down the drive whilst beating, and suffered at least four good bongs on the head from the wing falling.

Its back to almost as new now.

The Ironic thing is that since I'm converting to chrome bumper, this area has to be cut away and smooth pieces welded in.

The wing then has been rubbed all over, inside and out, sprayed in grey primer several times between applications of small amounts of filler.

Still, at least all the captive nuts are all ok.

Next job on the list is fitting a repair panel to the RH footwell where it joins the inner sill.

Andy from Doncaster donated this part when I bought the LH sills from him on good ol E-bay.

Even though the panel is for the wrong side I'm only using the inner 1" so it will match perfectly.

See the devil wing below, and I promise to post more often.

More soon avid readers

Rust........in all the wrong places !

Well..........removed the RH outer sill rather easily. Six spot welds and a few easy whacks with the multi-tool ( scraper/chisel/upholstery/screwdriver thingy) and off it came.

The good news is the inner membrane is in near perfect condition, as is the castle rail.

So I've decided not to replace these. The inner sill is also good too !!!

Its not all good news though.

The front bulkhead, where the sill front meets is well.....as mess !

Its really weird that the car has rusted in all unexpected places, as well as expected places on different sides.

I decided to chop off all the rust with the newly refurbished grinder ( having replaced the carbon brushes with the proper items)

So look see.............

The upturned flap on the castle rail is going to be tricky to repair. Its in good condition.

However, its the top most part of three layers of steel. The next layer is the front bulkhead ( rusty where cut away) and behind that is the upturned flap on the end of the inner sill.

Also another tricky part is the end of the membrane. I cut it away a bit and bent it out to investigate the inside.

I think I may replace the first two or three inches of this and it will allow prior access to the end flappy area.

In a fit and flurry of DIY we have re-painted the whole of the dining room.

Well, wifey started it.......all ar*e about face and in a terrible mess. Still credit to her she stuck in there and cried HELP when it got tough.

So, early last Saturday I got stuck in, moved shelves and heavy objects etc, and completed it by Sunday late lunchtime

Trouble is now though she's already planned another two rooms for the next few days, for the same treatment. Cunning devil has been saving it for my Hols without letting on. I'm sure it was all a scheme to keep me away from the MG. I think she knows how to make motor brushes wear and welding gas to evaporate ( witchcraft ?..... feminine intuition or just plain bad luck ?)

Considering I'm on holiday now for two weeks and spending them at home I can't see where the rest/relaxation is going to come................................Ha!! Wifey says...........spend a day in my shoes anyday you like Mr " I've had a long busy day at work, too tired to do DIY but enough energy to fiddle with your hobby" ( No....."hobby" is not a euphemism for that precious and rewarding universal boys toy we discovered in early teens)

Once that round of DIY is now complete I removed some more engine ancillaries and even had the foresight to "borrow" a large plastic storage box from work ( we specialise in machinery to print them so we have lots skulking around the factory)

It looks rather empty in there.

Whilst Wifey is still to the forefront this holiday I used some female logic on her !!

And guess what................................................................It worked.

As I explained how much the three part LH sills cost and my joy at not having to buy all three , hence SAVING on this part of the project, I can now go and buy another RH rear wing complete like last time, you remember dear, back in May, my birthday, when we had a fun day out together and visited the MG hive............

Yes dear, what fun that was............we'll go again soon. But not until you've finished all the decorating, spent time away in Chester next week on a shortened holiday, been to see your beloved team play with No 1 son, and with whats left you can buy all the panels you want.

Well it sort of worked. Lets get in the good books first then apply more tactics.

More soon.........Thanks for the link Rick

If only I'd waited........or been a little less impatient

I've done a stupid and silly thing.

Annoyed at the the yet again death( well soldiering on bravely but intermittently) of my trusty angle grinder I decided to remove the exhaust.

Rear end not too bad.

Middle section easy.

Front end.......so far so good, five of the six nuts undone.

The last one..............Impossible.

I'm under the car looking up at the manifold join. Yes the first five were a little tricky and awkward. I can only just see the sixth, let alone get the socket and extension onto it.

The trouble is the sump edge is in the way. It won't allow the socket to sit square on.

After several attempts, bruised knuckles, rust flakes in both eyes and oil/grunge in back of head I called it a day.

Well almost.

In a fit of pique I whacked the grinder one more time and it sprang into life.

So under the car I crawled and cut the exhaust in two just after where two pipes become one at a thick flange.

I thought it the only way to remove the damn thing. The last bolt was rounded off, and too inaccessible to get so much as a finger there, let alone a grinder or wrench.

So in I went with the grinder. Grinder protested loudly but after 5 mins there it was.

In two more manageable halves........................but see later.......................

Oh I forgot, to celebrate finishing one side the whole clan helped me move the car the other way round in the drive.

This involved moving both normal cars to way up the other end of the Cul-de-sac.

Pushing a very heavy car (including tool contents inside) onto the road at 45 degrees.

Pushing a little further down road. Son armed with patented vehicle halting device ( half housebrick) There's no brakes on the car cause I've removed them and the steering is very very heavy.

Then push back into drive.

At this point I'd like to thank the newish and so far never speaking, neighbour opposite and Dutch relative/friend.

..............................................................................................For watching............................................... while this old fart, his unfit wife with a bad back and two skinny thirteen year old twins ( one of each) struggle somewhat.

They ( two males 35-45 years of age) spent the whole afternoon looking at the engine of their car and then looking at the toolbox.

I hope they enjoyed watching us from 15 feet away across the road.

Its the other way round !!

The following day I decided to remove some engine ancillaries.

Carbs came away nicely after locating the bolts.

Since the under bonnet was covered in a poor excuse for sound proofing that hanging off in most places the whole engine bay is covered in "FLUFF".

"Yes, fluff"

Well more like horeshair, but its everywhere. And mixed up with loads of rust and lots of oil.

So cleaning the carbs will be interesting. So will the whole engine bay actually.

Removed centre inlet manifold, easy.

Even the dead rusty and often snapping exhaust studs came undone.

Its then that the manifold fell down and to one side.

Yes the difficult to get at nut was now easily accessible from underneath.

WHAT A PRATT.............I cut the exhaust in two for nothing !!!

If I'd removed said items before attempting the manifold studs underneath i would never have rounded off the last nut...........doh !!!.

So, lifted it clear and deposited both halves at back of shed out of sight.

Following day removed alternator, coil and dizzy lid + oil filter. Yes. I did remember to label all the wires up................sometimes I function almost normally.

Here's a few shots of my rust investigations of the the as yet untouched RH side.

This is a view looking forward at the A Post top. Worrying and scary.

This is after my head exploded after finding more rust.

Have no clue how I'm gonna repair these little beauties.( books and toilet springs to mind)

Suppose it explains me turning my attention to the engine.

Footnote.

The grinders died well and truly. No amount of whacking makes it start. Ordered new bushes from Screwfix ( £ 6.50, robbing dogs...........the whole grinder was only £17.00)

CO/Argon bottle on MIG welder also empty.

Spotweld drill bit blunt as hell.

Time for some time off or DIY......................yipee says Wifey. Personally I want a holiday.

More soon hopefully.

Go here, It's the funniest thing I've read in a long time

Just a quickie post to share with you all, but very very funny.

Its right up my street as its toilet humour( Laxatives actually) at its best.

Stick with it and read all the posts by Blu-Tone.

Its actually from a Mountain Bike message board.

One day 'Ill tell my funny story of a hospital visit. I'd have to embellish it somewhat but it would not be a patch on how Blu-Tone tells his !!!!

Link = http://www.singletrackworld.com/forum/read.php?f=2&i=3145351&t=3141618#reply_3145351

Tool trouble then rapid progress

Here's the part I'm damn proud of.

It involved bending a section of the curved rear valance ( above the square hole) then welding in place and having a 5/10mm lip to place the flat plate onto.

The large vertical weld is where the rear valance and wing end did not meet exactly.

I placed a strip of steel approx 1" wide to the rear, bent to fit the curve and welded inplace.

I managed to fill most of the non meeting edges with weld.

The flat plate that rests in the base of the pointy thing and upto/on the rear boot corner was quite tricky. I got through lots of cardboard making the right shape template.

Still, it all went very well with no probs...............the secret to welding is grind all the things nearby shiny, get a good earth and listen to the weld..............like rapidly cooking bacon.



The only Blot on the landscape was the angle grinder dying.

Ma in Law bought it for me last x-mas from screwfix. Not a top make ( NOTE..always buy Bosch if your serious) but its been the most used tool and definitely a requirement.

However, one day it just did not switch on.

Checked the fuse....ok

Checked the kitchen socket....ok

Unpluged and removed the disc and guard...........scary stuff as this tool scares the life out of me.

Then I noticed two protrusions each side of the main body with a large screwdriver slot in the end. Removed these and the commutators sprang forth with a tiny blob of an excuse for a carbon block.......................Disaster, should I persue the probably frustrating and longwinded course of new parts through Screwfix, or should I source locally.

Anyway, since the rains was still with us I decided on local. B&Q ect, shed no light or idea on tool spares.

In fact I dont think any of the staff even knew what a motor commutator was.

Now, may I get on my high horse here. B&Q ect may be cheap, convenient and always open but there not a patch on" proper" hardware places. We have two in my town.

One just like"open all hours" for hardware only. Its amazing. Ask one of the elderly staff for a lock and they will have it all, and explain about 2,3 and 5 lever mortices, ease of installation and price and insurance complications and reliability. Same goes for aluminium ladders, parrafin,

Chicken wire, hinges, wheelbarrows, hammers, bolts and screws + trillions of other stuff.

All served by people friendly and happy and willing to talk and dressed in regulation stores issue Brown smock. Thats just one place.

The other place is for things electrical/electronic.These guys know it all, have it all, but are on a slightly different planet. It scares me a little.

So in I waltz with one mangled commutator. Have you got one of these ?

No, but we have on similar that you can "modify"

Well, for £2.30 why not.

Thats when the probs started. The carbon block was too large so I filed it with my swiss file, on the worktop in the kitchen.......................Big mistake, the dust is immoveable and gets everywhere. Wifey not happy.

Moved outside to workmate and rushing due to fact that imminent heavy storm due.

Still difficult to insert and remove carbon block. Then cover screw would not screw in totally.

Snipped spring shorter. Still no joy. Bent copper ends from carbon block/copper wire in several shapes, still no joy. However, shaking said grinder did momentarily show some life.

Anyways, to cut a long story short I buggered one and re-used the old one which was OK and fiddled the other eventually after lots of shaking and "gentle taps on the plastic retaining screw".

It now works...................thank **ck for that. It was almost touch and go between throwing it away and being electricuted in the rain outside.



Now we've had some respite in the rain the progress above has been made and not a small amount of filling and sanding.

Look......................................rapid progress.

Hours of sanding the rear lower valance applied by the previous owner left no nasty horror sories. Only a 50p sized hole in the very centre of the R/H crossmember end. Easily remedied by some fancy shaping of a 1mm thick steel and good welding/ filling skills.

Even after a good coat of primer some low spots were evident, so another round of filling and sanding. I must say this is very ffffrustrating. The different grades a sandpaper, sanding block, dust, mess, armache and annoyance that a pristine shape don't emerge.

So I moved onto removing the complete exhaust. Easy enough on the length of the car.

Easy enough on five of the six nuts under the manifold although three were a bit fiddly.

The six'th (NOT SIKTH, which is how annoying people pronounce it) however seems impossible to get to. The shaft of the ratchet extension is too thick, the engine base/sump flange won't allow the the socket to sit on fully since the extension is not perfectly vertical.

So a point to ponder on whilst the wifey tries to fill my head with DIY projects and things to do of a summer day in the garden.

More soon folks......................oh by the way visit Ricks site.........He's got more money and tools than me and is making a real good job of it.

http://rick-mgbgt.blogspot.com/

A different corner

So I'm moving onto the rear corner now. Most of the LH side body is DONE !!!

The wing fits as well as its ever going to fit, and is covered in primer and red oxide. The doors in the correct place ( not quite but the Phillips screws in the hinge need drilling out and I ain't got any replacements, so its near enough for me at this stage, it closes and looks neat all round)

The all shiny new wing attaching bolts fitted.

Rear wing welded in position. ( almost. Need new inner outer section, see earlier re incorrect item purchased.)

I'm ignoring the 50p sized hole in the rear window edge. It looks fiddly to repair and is covered by chrome trim eventually.

That means a quick fix for me then.........maybe, and some time next summer.

Oh by the way have we had this summer yet ?????

Here's a view of what I've been up to.

Since the car is being converted to chrome bumpers I have to add the RH side pointy thing at the base of the lights. This is another item I purchased NEW from MGB Hive a few months ago on a rare spending spree. I actually comes complete, so I just chopped off half.

I have to add a couple of patches to base of rear valance where its welded to inner boot tray .

The fiddly bit is the horizontal section inside the pointy thing and up to the valance.

Mine has completely rusted away under the gauze and deep body filler that was there.

Still, I'm becoming quite accomplished at cutting cardboard templates, jigsawing sheet steel, grinding and welding. Thats for the coming weekend if we have no rain or something that resembles summer.

Must stop complaining though,as last year when it was red hot ( ah.. a distant memory) I couldn't be bothered to make a start on cutting, welding and grinding.

Just to keep it interesting here's another photo of the rear end. Note the lower valance, completely covered in filler by the previous owner. Had a little poke around and spotted rust at the bumper mounting holes. So, maybe I need to sand all this off before starting the above. If its bad news though that means a complete rear lower valance at £80 quid, ouch !

That reminds me. Since I,m over 18 months into the project I decided to have a review of the most useful tools to date. This is prompted by the fact that when I started I had absolutely no tools. In fact it never occurred to me that I would need Imperial sockets and spanners

Well it did really occur, since I'd worn out at least one toilet seat reading all things MG.

So here's the list, in order of usefulness for restoring old BL cars on a budget :-

1/. Trim tool remover.

Its a cross between a narrow paint scraper and a wide screwdriver. I got it for free as a print sample during a customer visit. I use it all the time for a/. Poking rusty holes, b/. separating spot welds, c/. smoothing bubbly paintwork, d/. removing underseal and rubberised gooey stuff, e/. prising panels and stuck down trim bits, f/. Phillips and standard screw removal. g/.wrapping J cloth round to clean inside light lenses and various parts.

2/. Penetrating Oil

As a matter of habit and long standing ritual I spray every nut and bolt I can see regardless of when I'm working on them or not. This is done at least every 2 weeks.

3/. Trolley jack

The cars been up/down so many times in so many places this has proven invaluable together with the axle stands. Remember I have no garage to work in so positioning the car for long periods is important.

4/. Electric 4-1/2" Hand Grinder

Scary tool to use. Very noisy. Needs love and attention and several types of discs. The Flappey layered one has been good but also the thin slicing disc is just as valuable. Good for heavy steel removal, light polishing of steel, de-rusting and shaping steel.

5/. Hammerite Ku-Rust

When panels are inaccessible and too awkward to remove/replace or just covered in surface rust, just paint it on and it does its stuff. I use it loads.

6/. Heavy Aluminium faced hammer. Nuff said.

7/. Quality Imperial socket set.

See earlier posts for my folly at cheap and cheerful

8/. The wonderful Mr Porter and his MG restoration guide, closely followed by the DVD of the wonderful Mr Mark Evans "Is born" series of MG restoration.

9/. E-bay My main source of tools and parts, especially the MIG welder.

10/. Time and money.....................unfortunately I have very little of either.

More next week folks,

As you can see, or maybe not some things have been achieved.

I have spent lots of time getting the wing ready and prepared, mostly on the inside and adding filler to the sill/B-post join.

Why is it that things that seem to worry you most and up being the easiest to fix.

The wing mounting holes for one.

The beading and wing fit for another.

The fitting of the of the wing for yet another.

Anyways, back to the order of things since the last post.

I had applied lots of filler to the B-post/sill join and to the scuttle where it meets the wing top.

I must say that I ended up sanding most of it off.

Then the rain came....................and boy did it, in bucket loads.

So not much happened for the last two weeks, except for the rain.

Sunday evening saw a veritable monsoon, from 8pm onwards till about 10.30 next day.

During the brief interlude I noticed..........Horror of horrors that the blue cover over the MG had blown off some time Sunday evening/Mon morning and left the car open to the elements.

Well, elements is a pretty light word so I'll say pissing heavy torrential rain.

Luckily, only the outer edges of the inner car were damp with light rusting on the floor & sill areas. And for some strange reason one bucket in the back containing all my precision hammers 3 inches deep in water !!.

The blue Poly cover is pretty porous though, particularly where its been dragged over the roof on the ariel base. I did have a tennis ball over the protrusion but that's long gone into the void of disappearing restoration parts.

So Monday lunchtime off to good old B&Q during a firm but constant drizzle.

£3.99 for same Blue poly cover, 3 mtrs x 4 mtrs with fastening holes, what a bargain.

Gawd.......................what a size !!! You could cover half of Derbyshire with it.

Try fitting it in a drizzle and breeze enough to get you out of the harbour.

It was everywhere on the drive, Still its not porous (yet) and the biggest ball of wifey string helped to keep it in place, with the old ( porous yet much more manageable) cover over the top.It did its job for at least 2 weeks. Yes, that's how much rain we've had.

The work done to the inside of the wing worried me lots before I started.

It wasn't until a work related detour via Cambridge that I actually bought some more new stuff from the MGOC. A wing fitting kit to be precise, a 5/16 UNF nut, a 1/4 UNF nut and a headlight inner re-enforcing ring.

Spent all Saturday welding the 5/15 UNF nut under the wing top inner edge, making a cage for a strange British Leyland round 5/15UNF nut and welding up in same top inner edge, welding the 1/4 UNF nut to the inner wing mountings ( having first spent ages drilling out broken bolt and grinding away old nut ).

All just so the wing can go back on and be bolted in all its places.

Sunday saw me paint good old Hammerite Red lead all the inner wing rust prone areas, sand the sill B-post area, try again( 38th attempt) to remove the door hinges from the A post.

This but was aborted yet again.........which is a pity because the great big f**k off screwdriver I have has a hexagon on the shaft where it enters the handle so a ring spanner fits great and offers fantastic leverage. The phillips head is buggered though, thus it stays put....maybe !!

Ran a 5/16 UNF tap down the wing edge holes then undid the wing fitting kit.

Yipeeeeeee...........loads of new shiney screws, washers and spring washers + 3 nuts too !.

Fitted wing in a trice.......could even do the nuts up with fingers mostly.

Only had to use jack to press up bottom of wing so I could drill 3 holes to accept 3/16 screws with nut to attach to castle rail and jobs done!!!!!!!!!!!!!!!!!!!!! yes it fits and looks good!!!!

To think I started this blog and spent ages in deep mid winter removing the wing, and now here I am still in July deep mid winter fitting the wing.

Removed it though and sanded and cleaned everything down one side.

Sprayed lovely clean Grey primer on door, wing rear wing, B-post and sill area, A post and finally inner front wing area.

Here have a look..............................................

How good it is to see it looking like a car again........Its given me a real sense of achievement.

Next session should see the door hung, sort of, maybe finally or time to reconsider the phillips screws again, maybe leave them.

Wing fixed with all new shiney screws and bolts.

Sill finished ( still some slight filler spots to add to get nice even gaps) and to wing too, suffering collateral damage from being removed and trial fitted too may times.

Then weld rear wing and turn attention to rear of car..........Yes a new chapter, hopefully.

Its a little damp outside dear

What can I say other than the title. Since last applying filler to the B post/sill join and filler to the wing/scuttle join its been........................well I'll say .................... wet!

The last two weekends, nay weeks, has seen torrents of rain fall, all day,all night and in between. During last Mondays deluge a quick glance at the MG and its forlorn flapping blue poly cover saw lots of rain get inside. Mid-day off to B&Q to get a new Poly cover( in the pouring rain) .

My present cover has a hole where the roof section has an ariel base protuding.

Despite having the clever idea of wedging an old tennis ball on it, the constant removing and tie-ing down has made it as firm as a vicars handshake. Not to mention the elastic bungee cords frayed to within an inch of their life. In fact on Sunday the poor old MG spent the evening till Mon Morn with the cover hiding between the fence and the driveway gate.

Fortunately I got the last blue Poly sheet at B&Q and cheap it was too (£ 3.99) .

The trouble was thought.................................Its Huge !!!!

3 metres x 4 metres. Seemed OK when I bought it. But try covering a car with it in the pouring rain, using frayed and limp bungee cords and a howling wind.

I ended up using about 70 metres of string, over, under, around, between, up and round the MG. It looked like a drunkard had tried to wrap up a Holly bush there was so much Blue poly cover. However, it made it water proof ready for the onslaught or rain we had, er........still having actually.

Prior to thison Saturday, I did remove the front wing several times to try and get a good fit between the curvy scuttle base and wing top edge............ Impossible............!!!!

In desperation I fixed the front wing with the 5/16th UNF bolt nearest the said position.

Then added filler to the join and bead ( I previously welded the bead to the wing)

So my thinking was if the join was rubbish( uneven with gaps) bolt them together, add filler, let dry, remove wing , sand to perfection and re-fit wing nicely.

WRONG

On removing wing all the filler broke off, some filler stuck to inside of wing beading and some filler was well just ..........crap.

ABANDONED...................................time for a re-think.

It needs all its bolts and holes in wing ready and clean so it can be clamped tightly, then re assess.

So, on a trip to the far SE corner of our wind and rain swept counrty I diverted via Cambridgeshire to the MGOC.

I actually bought some new ( YES NEW ) stuff, a wing fitting kit containing all the correct screws , washers and bolts. Nice and shiney.............Lovely, and only £ 6.25 !

Also got the 5/15th UNF Nut which I had to gring off the wing when refurbing it and another nut 1/4 UNF which has a sheared bolt in it on the wing.

Whilst there I also bought the headlight re-enforcing panel. This part took the best part of a whole day to remove from the wing as it was rusty and deep inside the wing.

So...............................My plan is simple.

Fit both new nuts by mig welding them in place.

How to remove the existing nuts with broken bolts in is another story.

Then fit the wing with all the bolts and nuts. To assist matters I even bought a 5/16 UNF tap.

Please dont faint, its not new. It was £1.99 + 99p p&P on..........yes you've guessed good old E-bay.

So when the rain and wind stops I'll get busy. Oh and do the sanding of the B post too.

A little more of all life's joys and irritations

Not much has happened so far. MG wise I've pratted around doing nothing spectacular.

Well that's not exactly true.

I did set to to fit the inner wheelarch a few weeks ago. If you remember it was a panel I needed and was one of several bought as a birthday prezzie from MGB hive.

Anyways, I did all the correct things and lined it up, marked it + 1/2 inch and cut to the desired shape. Cut away the rusty wheelarch inboard of the 1/2 line.

I then set to attaching the wing, all well and good.

I spent the next few days(nay weeks) trying to get the inner wheelarch to fit the shape of the wheel arch and align front and back.

Impossible, so I left it for a further few days.

Then one bright and sunny Saturday I attacked it with renewed vigour and enthusiasm.

Gawd............................I know why it don't fit......................its the wrong side!!!!!!!!!!!

Yes, I had actually been given a RH side when I needed a left. No wonder in didn't fit.

I've not told wifey yet........No need really since I can use the panel for the RH side , but all in good time.

What I have done is welded the wing around the B post seam/door and sill area.

See Below..............................

I know the gap between the sill and b post base is a little large, but, well there really is no answer. When taking off the old sill the gap was even larger, I remember distinctly seeing all the lead loading ( Yes Lead Loading) running away as I ground through it. So It must have been made that way at good old Abingdon ( Swindon actually is where the bodies were assembled)

The front wing gap at the same spot is also same size.............WE really did know how to build cars, eh !

The gap is now full of the dreaded filler ( No I,m not going to spend several months learning how to lead load) and its waiting to dry as I write this.

I did go a bit mad with the filler and covered several spot weld and the rear wing top beading seam. So next post will be all about sanding filler........maybe.